Page 376 - Electrician 1st year - TT - Malayalam
P. 376

9   Smoke from motor       Overload.                Reduce the load.
                (motor burnt out)
                                       Shorter windings.        Rewind the windings.
                                       Faulty centrifugal switch.   Repair or replace the centrifugal switch.
                                       Frozen bearing.          Clean and lubricate or replace the bearing.
                                       Short capacitor.         Replace the capacitor.
             10   Rotor rubs stator    Dirt in motor.           Clean the motor.
                                       Burrs on rotor or stator.   Remove burrs.
                                       Worn out bearings.       Replace the bearing.
                                       Bent shaft.              Straighten or replace the shaft.
             11   Excessive bearing wear    Belt too tight tension   Correct the mechanical condition.
                                       Dirty bearings           Clean and lubricate or replace the bearing
                                       Insufficient lubrication   Lubricate with appropriate lubricant.
                                       Thrust over load         Reduce thrust load
                                       Bent shaft               Straighten or replace the shaft.
           12   Motor does not start      Defective capacitor.   Replace the capacitor.
                but will run in either   Contacts of centrifugal   Clean the contacts of the centrifugal switch and
                direction  when started   switch not closed.    check  for operation.  Replace, if found defective.
                manually               Starting winding open.   Solder the open joints or rewind the winding.
             13   Motor slows down and   Short circuited windings.   Rewind the windings.
                runs with insufficient   Open circuited windings.   Solder the joints; if not possible, rewind the windings.
                power under working    Shaft bent.              Straighten or replace the shaft.
                condition.
             14   Reduction in power of     Short-circuited or   Rectify or rewind the windings.
                the motor. Gets too hot   grounded windings.
                                       Sticky or tight bearings   Clean and re-lubricate the bearings.
                                       Interference between     Install new bearings.stator and rotor.


       ട്പതതിദതിന  അറ്ക്ുറ്പെണതി:  ഭാഗങ്ങൾ  തുണതി           വാർ�തിക അറ്കുറ്പ്ണതികൾ:ഇൈക്പ്ടതിക്ൽ റമ�ീൻ
       ഉപപോയാഗതിച്് വതൃത്തിയാക്ണം, പോ്റൊൺ  റബയെതിംഗ്       നീക്ം  റെയ്യുകയും  ഓവർപോഹാൾ  റെയ്യുകയും
       എണ്ണ പുരടേണം. റബൽറ്് റടൻ�നും ലവപോപ്ബ�നും             പോവണം.  വാർണതി�്  പ്പപോയാഗതിച്്  ലവൻഡതിംഗ്
       പരതിപോശാധതിക്ുക.                                     ഇൻസുപോൈറ്്  റെയ്യുക.  എൈ്ൈാ  റമക്ാനതിക്ൽ

       പ്പതതിമാസ  അറ്കുറ്പ്ണതികൾ:ലപ്ഗൻഡെതിന്റെ              ഭാഗങ്ങളും പരതിപോശാധതിച്് തകരാെുകൾ ഉറണ്ങ്തിൽ
       പ്പ ധ ാന    � ാ ഫോ്റ്തി ൽ    എണ്ണയും    പ്ഗ ീ സും    അത് പരതിഹരതിക്ുക.
       പുരടേുക.  ഇൻസുപോൈ�ൻ  റട്റെ്  നടത്ുകയും
       നൽകതിയതിരതിക്ുന്ന  �ീറ്തിൽ  പോരഖറപ്ടുത്ുകയും
       പോവണം.
























       356          ഇലക്്ടട്്രരീഷ്്യൻ (NSQF - പുതുക്തിയ 2022)  േതി. സതി .  റവണ്തി എക്്ടസതിർസസസ്ട 1.11.96
   371   372   373   374   375   376   377   378   379   380   381